Fastrax Workbench 5 supports all Fastrax GPS receivers
New Fastrax Workbench 5 supports all Fastrax GNSS receivers that are configured to output NMEA protocol.
IMPORTANT: Fastrax Workbench 5 setup will NOT attempt remove or upgrade any GPS Workbench versions prior to version 4.5. If you do not use the earlier versions and have any of them installed, it is recommended that you remove the earlier versions manually using Control Panel.
Fastrax Workbench 5 is a major improvement to previous version and contains support for multi-GNSS receivers (GPS and Glonass), SBAS and QZSS. Online map display is included.
If you have any problems, please do not hesitate to contact support@fastraxgps.com
- Download Fastrax Workbench 5 (version 5.01.2081 – Updated March 21st, 2012)
New features
- Improved support for IT600 series
- Support for IT530 series
- Online map display
Installation requirements
- Installing Fastrax Workbench 5 requires that you have Microsoft Visual C++ 2010 runtime and .NET 4.0 Framework installed. Fastrax Workbench 5 setup will attempt to download and install these packages for you automatically. So normally you do not have to take any special actions, but if you have any problems, you can download the packages manually from Microsoft :
- Note also, that if you wish to save Fastrax Workbench 5 setup to USB stick or CD and run the setup without active Internet connection, you need also to include vcredist_x86.exe, that is available from Microsoft using the link. Run Microsoft Visual C++ 2010 Redistributable (vcredist_x86.exe ) setup as well as .NET Framew0rk 4 setup before running Fastrax Workbench setup. With active Internet connection, you do not normally need to do anything special.
- To use Fastrax Evalution Kit with Fastrax Workbench 5, you also need Fastrax USB drivers that are available below.
Supported operating systems
Fastrax Workbench 5 has been tested under following operating systems:
- Windows XP (x86) with Service Pack 3
- Windows Vista (x86) with Service Pack 2
- Windows 7 (x86 and x64) with Service Pack 1
Important: Fastrax Workbench is NOT supported in 64-bit versions of Windows Vista, Windows Server 2008, Windows Server 2003 R2 and Windows XP.
Legal notice
Copyright (C) 1999 – 2012 Fastrax Oy
This computer program is property of Fastrax Ltd.
The program is free to use, but may not be retransmitted or redistributed without written permission from Fastrax Ltd. (“Fastrax”). You may not upload this program or any part of it to any public server, on-line service, network, or bulletin board without prior written permission from Fastrax. You may not make copies for any commercial purpose. You do not obtain any ownership right, title, or other interest in Fastrax’ or possible third party trademarks or copyrights by downloading, copying, or otherwise using this software.
This program is free of computer viruses, however, for your own protection, you should virus scan these files again after you have downloaded them. You assume the entire risk related to your use of this data. Fastrax is providing this computer program “as is,” and Fastrax disclaims any and all warranties, whether express or implied, including (without limitation) any implied warranties of merchantability or fitness for a particular purpose. In no event will Fastrax be liable to you or to any third party for any direct, indirect, incidental, consequential, special or exemplary damages or lost profit resulting from any use or misuse of this computer program.
Contact information:
Address: Itsehallintokuja 6, 01200 Espoo, Finland
Email: support@fastraxgps.com
Internet: http://www.fastraxgps.com
Fastrax USB Drivers
These drivers are compatible with Fastax Mini Evaluation Kit as well as Track&Trace Platform.
Compatible operating systems: Windows XP (32-bit), Windows Vista (32-bit), Windows 7 (both 32-bit and 64-bit).
PLEASE NOTE: Windows Vista 64-bit operating system is NOT supported.